http://pro-streetcycles.com

Online Catalogue

Pro-Street Cycles

Pro-Street Ultra LED Light Products

Pro-Street Ultra LED Tailight & Indicator Bulbs


	*Ultra Bright White LED Replacement Tailight Bulb* 15mm Bayonet 24 White LED Stop & Tail Special Its special because it has 18 Hyper Bright LEDs pointing at the front and 6 to the sides to reflect the light to your reflectors making the angle much wider - we use these on our bikes and they are twice as bright as the standard bulbs even using the standard Red lens. A filament bulb can take up to 0.2 of a second to reach maximum intensity where as an LED reaches maximum intensity instantly. When used as a brake light, this time saving could reduce the following vehicles braking distance by up to 1.5 metres when travelling at 70 mph. These new L.E.D bulbs use only 1/50th the power of a conventional bulb. These bulbs make full use of the reflector and produce a very wide beam of light. This safety aspect coupled with a typical power requirement of less than 1/50th of an equivalent size bulb, virtually no heat output and an average 50,000 hour life, and resistance to vibration, the advantages seem endless. Hyper White 24 -LED 12VDC replacement bulb 15mm Dual Contact Bayonet Base Power Consumption 40ma Rear 90ma Brake Brightness Rating - MCD 140,000 Mcd The Size of the Bulb Head is 26mm and should fit most tailights. *Standard Tailight fitted with a Pro-Street Cycles Ultra Bright Red LED Replacement Tailight Bulb!!* Price: £11.50 Including VAT at 17.5% Live Currency Conversion into Euros \| US Dollars \| Other (To be used only as a guide.)


*Ultra Bright Red LED Replacement Tailight Bulb* 15mm Bayonet 24 Red LED Stop & Tail Special Its special because it has 18 Hyper Bright LEDs pointing at the front and 6 to the sides to reflect the light to your reflectors making the angle much wider - we've used these on our own bikes and they are twice as bright as the standard bulbs even using the standard Red lens. A filament bulb can take up to 0.2 of a second to reach maximum intensity where as an LED reaches maximum intensity instantly. When used as a brake light, this time saving could reduce the following vehicles braking distance by up to 1.5 metres when travelling at 70 mph. These new L.E.D bulbs use only 1/50th the power of a conventional bulb. These bulbs make full use of the reflector and produce a very wide beam of light. This safety aspect coupled with a typical power requirement of less than 1/50th of an equivalent size bulb, virtually no heat output and an average 50,000 hour life, and resistance to vibration, the advantages seem endless. Hyper Red 24 -LED 12VDC replacement bulb 15mm Dual Contact Bayonet Base Power Consumption 40ma Rear 90ma Brake Brightness Rating - MCD 140,000 Mcd The Size of the Bulb Head is 26mm and should fit most tailights. *Standard Tailight fitted with a Pro-Street Cycles Ultra Bright Red LED Replacement Tailight Bulb!!* Price: £8.99 Including VAT at 17.5% Live Currency Conversion into Euros \| US Dollars \| Other (To be used only as a guide.)


	*Ultra Bright Amber Indicator LED Replacement Bulb* (382)15mm Bayonet 24 Amber Indicator LED Single Filament. Its special because it has 18 Hyper Bright LEDs pointing at the front and 6 to the sides to reflect the light to your reflectors making the angle much wider. A filament bulb can take up to 0.2 of a second to reach maximum intensity where as an LED reaches maximum intensity instantly. Hyper Amber 24 -LED 12VDC replacement bulb 15mm Single Contact Bayonet Base Equal Pin (Please check before ordering) Power Consumption 90ma Brightness Rating - MCD 160,000 Mcd The Size of the Bulb Head is 26mm and should fit most standard indicators. Bulbs supplied are SINGLE CONTACT (not dual as shown). Price: £8.99 Including VAT at 17.5% Live Currency Conversion into Euros \| US Dollars \| Other (To be used only as a guide.)


*Load Resistor Kit (2 Per Kit)* When fitting our LED indicator bulbs if you find the Indicators Flash rapidly then you need to use a Load Resistor Kit. Resistors can be connected across the turn signal bulbs to simulate the load of a regular filament bulb (2 Amp load). This will solve LED related turn signal problems such as hyper flashing, no flashing or burnt out bulb indications. One resistor is required for each turn signal bulb. Includes gel filled moisture resistant splice taps. CONNECTION INSTRUCTIONS: Using included splice taps, connect one wire to ground and the other wire to the turn/brake wire. You do not have to cut your bike's wires. Squeeze splice taps with pliers. One Load Resistor required for each turn signal bulb. Please note that no instructions are include with these kits. Price: £9.99 Including VAT at 17.5% Live Currency Conversion into Euros \| US Dollars \| Other (To be used only as a guide.)